11. IETI, Isogeometric Tearing and InterconnectingStefan K. Kleiss, Clemens Pechstein, Bert Jüttler, Satyendra Tomar, 2012, izvirni znanstveni članek Ključne besede: isogeometric analysis, NURBS, domain decomposition, FETI, IETI
Objavljeno v RUNG: 13.11.2018; Ogledov: 3143; Prenosov: 0
Gradivo ima več datotek! Več... |
12. |
13. In-situ XAS analysis of nanoshaped CuO/CeO2 catalysts used for N2O decompositionIztok Arčon, Maxim Zabilsky, Petar Djinović, Albin Pintar, 2018, objavljeni povzetek znanstvenega prispevka na konferenci Opis: The goal of this research is to establish the working state and correlations between atomic structure and catalytic activity of nanoshaped CuO/CeO2 catalysts used in N2O decomposition reaction. The catalysts contained CuO nanoclusters dispersed over different CeO2 morphologies: nano-rods and nano-cubes. N2O is a side product of nitric and adipic acid production and a very potent greenhouse gas that is formed in amounts estimated at about 400 Mt/a of CO2 equivalent. Consequently, the development of robust, active and selective catalysts for N2O decomposition is of a great environmental and economical interest. CeO2-based materials promoted by CuO represent a new class of catalysts that exhibit considerable activity in N2O decomposition reaction between 300 and 500 °C [1-3], and are significantly cheaper and more efficient than Pt, Pd or Rh based catalysts.
In order to maximize the efficiency of the catalyst, the active site in this reaction needs to be identified and the mechanism clarified. In-situ Cu K-edge and Ce L3-edge XANES and EXAFS analysis was done on a set of CuO/CeO2 catalysts with different ceria morphology (nano-cubes, nano-rods) and Cu loadings between 2 to 8 wt. %, during N2O decomposition reaction, under controlled reaction conditions at 400 °C. The XAS spectra were measured in-situ, in a tubular reactor, filled with protective He atmosphere at 1 bar, first at RT, then during heating, and at final temperature of 400 °C, during catalytic reaction, when the catalyst was exposed to a small amount (0.2 vol%) of N2O mixed with He.
The Cu K-edge and Ce L3-edge XANES and EXAFS analysis reveals changes in valence and local structure of Cu and Ce in the CuO/CeO2 catalysts. In the initial state (in He at RT), copper is present in the form of CuO nanoparticles attached to the CeO2 surface. After heating in He to 400 °C, partial (10%) reduction of Ce [Ce(IV)→Ce(III)] is detected, significant part of Cu(II) is reduced to Cu(I) and Cu(0) species, and direct Cu-Cu bonds are formed. During catalytic N2O decomposition at 400°C, all Ce(III) is oxidized back to Ce(VI), and a major part of Cu is oxidized back to Cu(II), with about 5% of Cu(I) remaining in equilibrium state. Observed structural and valence changes of copper strongly depend on its loading and CeO2 morphology.
With systematic In-situ XAS analysis of different nanoshaped CuO/CeO2 catalysts, we identified the structural characteristics and changes of Cu and Ce phases during catalytic N2O decomposition reaction, which could lead to identification of the active catalytic site during the reaction and further improve the performance of these promising catalytic materials.
Ključne besede: EXAFS, CuO/CeO2 catalyst, N2O decomposition
Objavljeno v RUNG: 12.09.2018; Ogledov: 3766; Prenosov: 0
Gradivo ima več datotek! Več... |
14. Real-time motor unit identification from high-density surface EMGVojko Glaser, Aleš Holobar, Damjan Zazula, 2013, izvirni znanstveni članek Opis: This study addresses online decomposition of high-density surface electromyograms (EMG) in real-time. The proposed method is based on previouslypublished Convolution Kernel Compensation (CKC) technique and sharesthe same decomposition paradigm, i.e. compensation of motor unit action potentials and direct identification of motor unit (MU) discharges. In contrast to previously published version of CKC, which operates in batch mode and requires ~ 10 s of EMG signal, the real-time implementation begins with batch processing of ~ 3 s of the EMG signal in the initialization stage and continues on with iterative updating of the estimators of MU discharges as blocks of new EMG samples become available. Its detailed comparison to previously validated batch version of CKC and asymptotically Bayesian optimal Linear Minimum Mean Square Error (LMMSE) estimator demonstrates high agreementin identified MU discharges among all three techniques. In the case of synthetic surface EMG with 20 dB signal-to-noise ratio, MU discharges were identified with average sensitivity of 98 %. In the case of experimental EMG, real-time CKC fully converged after initial 5 s of EMG recordings and real-time and batch CKC agreed on 90 % of MU discharges, on average. The real-time CKC identified slightly fewer MUs than its batch version (experimental EMG, 4 MUs versus 5 MUs identified by batch CKC, on average), but required only 0.6 s of processing time on regular personal computer for each second of multichannel surface EMG.
Ključne besede: discharge pattern, high-density EMG, surface EMG, motor unit, real time decomposition
Objavljeno v RUNG: 05.01.2016; Ogledov: 5380; Prenosov: 0 |
15. |
