Repozitorij Univerze v Novi Gorici

Iskanje po repozitoriju
A+ | A- | Pomoč | SLO | ENG

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 3 / 3
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
BiVO3: A Bi-based material with promising uv-visible light absorption properties
Matjaž Valant, 2017, izvirni znanstveni članek

Najdeno v: ključnih besedah
Povzetek najdenega: ...magnetoelektrik, fotokatalizator, absorpcijske lastnosti...
Ključne besede: magnetoelektrik, fotokatalizator, absorpcijske lastnosti
Objavljeno: 09.11.2017; Ogledov: 917; Prenosov: 0
.pdf Polno besedilo (1,48 MB)

2.
Visible-light photoactivity of Bi-pyrochlore
Matjaž Valant, Metka Benčina, 2017, objavljeni povzetek znanstvenega prispevka na konferenci (vabljeno predavanje)

Najdeno v: ključnih besedah
Povzetek najdenega: ...piroklor, fotokatalizator, nanostrukture...
Ključne besede: piroklor, fotokatalizator, nanostrukture
Objavljeno: 09.11.2017; Ogledov: 850; Prenosov: 0
.pdf Polno besedilo (2,71 MB)

3.
XAS studies of Sn modified TiO2 coatings
Urška Lavrenčič Štangar, Iztok Arčon, Ksenija Maver, 2018, objavljeni povzetek znanstvenega prispevka na konferenci

Opis: Coatings based on TiO2 are extensively investigated material for the preparation of surfaces which are referred as self-cleaning. Under solar illumination these coatings catalyze pollutants degradation and enhance their removal from the surface due to photoinduced superhydrophilicity [1]. There are two main drawbacks of using pure TiO2 (anatase) as a photocatalyst; i) its band gap lies in the UVA region so it can exploit only a part of the sunlight spectrum, and ii) it has a high degree of recombination between photo generated electrons and holes on the surface. There are various strategies to improve the photocatalytic efficiency of TiO2, one of them is the modification with transition metals. Based on our previous experiences with sol-gel synthesis of low-temperature TiO2 thin films [2], we prepared a series of Sn modified TiO2 photocatalysts. As a starting material only organic (Ti and Sn alkoxide) precursors were used. The loadings of Sn cations were varied in the range of 0.05 to 20 mol.%. The coatings, deposited on glass substrates by dip-coating technique, were dried at 150 oC. In addition, another set of photocatalyst coatings was prepared by further calcination at 500 °C in air. The comparison of photocatalytic activities of Sn modified TiO2 to unmodified TiO2 showed that Sn loadings in the range of 1-10 mol.% improved photocatalytic activity up to 8 times. At lower loadings of Sn, the photocatalytic activity was improved only by 30 %. After the coatings are calcined, their photocatalytic activity was significantly reduced. The objective of the research was to examine the mechanism responsible for photocatalytic properties of Sn modified TiO2 and to to clarify the role of Sn cations in the TiO2 photocatalytic process. For this purpose, Sn and Ti K-edge XANES and EXAFS analysis was used to precisely determine the local structure and the site of incorporation of Sn cations on titania nanoparticles in the coatings. We examined the hypothesis that the solid-solid interface was a crucial structural feature that facilitates charge separation and enhances photocatalytic efficiency of titania.
Najdeno v: ključnih besedah
Ključne besede: Sn, EXAFS, TiO2 fotokatalizator
Objavljeno: 12.09.2018; Ogledov: 482; Prenosov: 0
.pdf Polno besedilo (97,78 KB)

Iskanje izvedeno v 0 sek.
Na vrh