Repozitorij Univerze v Novi Gorici

Iskanje po repozitoriju
A+ | A- | Pomoč | SLO | ENG

Iskalni niz: išči po
išči po
išči po
išči po
* po starem in bolonjskem študiju

Opcije:
  Ponastavi


1 - 2 / 2
Na začetekNa prejšnjo stran1Na naslednjo stranNa konec
1.
Extraction of Organochlorine Pesticides from Plastic Pellets and Plastic Type Analysis
Maryline Pflieger, Petra Makorič, Manca Kovač Viršek, Špela Koren, 2017, pregledni znanstveni članek

Opis: Plastic resin pellets, categorized as microplastics (≤5 mm in diameter), are small granules that can be unintentionally released to the environment during manufacturing and transport. Because of their environmental persistence, they are widely distributed in the oceans and on beaches all over the world. They can act as a vector of potentially toxic organic compounds (e.g., polychlorinated biphenyls) and might consequently negatively affect marine organisms. Their possible impacts along the food chain are not yet well understood. In order to assess the hazards associated with the occurrence of plastic pellets in the marine environment, it is necessary to develop methodologies that allow for rapid determination of associated organic contaminant levels. The present protocol describes the different steps required for sampling resin pellets, analyzing adsorbed organochlorine pesticides (OCPs) and identifying the plastic type. The focus is on the extraction of OCPs from plastic pellets by means of a pressurized fluid extractor (PFE) and on the polymer chemical analysis applying Fourier Transform-InfraRed (FT-IR) spectroscopy. The developed methodology focuses on 11 OCPs and related compounds, including dichlorodiphenyltrichloroethane (DDT) and its two main metabolites, lindane and two production isomers, as well as the two biologically active isomers of technical endosulfan. This protocol constitutes a simple and rapid alternative to existing methodology for evaluating the concentration of organic contaminants adsorbed on plastic pieces.
Ključne besede: Environmental Sciences, Issue 125, Microplastics, resin pellets, pesticides, persistent organic pollutants, organochlorine pesticides, dichlorodiphenyltrichloroethane, endosulfan, hexachlorocyclohexane, lindane, Fourier transform infrared spectroscopy, pressurized fluid extractor
Objavljeno v RUNG: 10.07.2017; Ogledov: 5468; Prenosov: 0

2.
Analysis of polychlorinated biphenyls adsorbed on plastic pellets: Comparison of extraction techniques
Petra Makorič, 2017, magistrsko delo

Opis: Plastic resin pellets are one of the main components of plastic fragments in the marine environment. They are small granules, generally cylinder or disk-shaped, with a diameter of a few millimetres used as industrial raw material for the production of plastic manufactured items. Resin pellets can be unintentionally released to the environment during manufacturing and transport, and can reach the ocean through processes such as surface run-off. Because of their environmental persistence, they are widely distributed in the oceans and on the beaches, all over the globe. Plastic pellets are also a sink of toxic compounds such as polychlorinated biphenyls (PCBs) that are present in the environment. During this thesis, we designed a protocol for extracting and analysing PCBs from marine plastic resin pellets. Although pressurized fluid extraction (PFE) is not commonly used in the field of microplastics, it is a reliable and efficient technique applied in other research areas. Thus, this method was tested in this work. PCBs were extracted from plastic pellets with PFE at 65 ºC and under 100 bar with hexane. Then, the extracts were concentrated to 1 mL, cleaned up on Florisil cartridge through solid-phase extraction. Prior to analysis on GC-ECD, the cleaned extracts were concentrated again. In the second part of the thesis, the following four extraction techniques of PCBs from plastic resin pellets were compared: Soxhlet extraction, PFE, ultrasonication and maceration. The obtain results have shown that the best efficiency and repeatability of extraction is achieved with PFE. In case of Soxhlet extraction, the results were unrepeatable. Maceration and ultrasonication had 40-45 % lower extraction efficiencies than PFE.
Ključne besede: PCB, plastic resin pellets, pressurized fluid extraction, Soxhlet, maceration, ultrasonication, microplastics
Objavljeno v RUNG: 22.06.2017; Ogledov: 6065; Prenosov: 270
.pdf Celotno besedilo (1,95 MB)

Iskanje izvedeno v 0.01 sek.
Na vrh