Repozitorij Univerze v Novi Gorici

Izpis gradiva
A+ | A- | Pomoč | SLO | ENG

Naslov:Microfluidic flow injection thermal lens microscopy for high throughput and sensitive analysis of sub-μL samples
Avtorji:ID Liu, Mingqiang, UNG (Avtor)
ID Malovrh, Sara, UNG (Avtor)
ID Franko, Mladen, UNG (Avtor)
Datoteke:.pdf Cr(VI).pdf (828,33 KB)
MD5: DCC2EA043B403CDADC4349647FD888D3
 
Jezik:Angleški jezik
Vrsta gradiva:Delo ni kategorizirano
Tipologija:1.01 - Izvirni znanstveni članek
Organizacija:UNG - Univerza v Novi Gorici
Opis:An analytical method combining microfluidic flow injection analysis (μFIA) with thermal lens microscopy (TLM) was developed for high throughput and sensitive analysis of sub-μL samples. Performance of the μFIA-TLM was validated for detection of hexavalent chromium [Cr(VI)] in water samples. At different sample injection volumes, detection positions and flow rates, influences of the reaction time and the diffusion of Cr-diphenylcarbazone (DPCO) complexes on the μFIA-TLM signal were investigated. Photodegradation of the Cr-DPCO complex was clearly observed when the absorbed photons per Cr-DPCO is above 1600. After optimization of the TLM with respect to rapid flows (up to 10 cm/s), we achieved a limit of detection of 0.6 ng/mL for Cr(VI) in a 50-μm deep channel. Impacts of interfering ions [V(V), Mo(VI), Fe(III)] on the Cr(VI) determination were found to be small. Cr(VI) in real samples from a cement factory were determined and found in good agreement with results of spectrophotometry. This μFIA-TLM shows advantages over its conventional counterpart, such as eliminating additional sample conditioning, reducing over 100 times the sample consumption to sub-μL and over 10 times the time required for one sample injection to a few seconds (up to 20 samples/min). The optimized μFIA-TLM setup can be applied for fast and sensitive analysis of nonfluoresent sub-μL samples in rapidly flowing mediums.
Ključne besede:Spektrometrija TLS, mikroskopija TLM, mikrofluidika, krom (VI)
Verzija publikacije:Recenzirani rokopis
Leto izida:2016
Št. strani:8
Številčenje:8
PID:20.500.12556/RUNG-2328 Novo okno
COBISS.SI-ID:4365051 Novo okno
DOI:10.1039/C6AY00932H Novo okno
NUK URN:URN:SI:UNG:REP:GJHFAC3A
Datum objave v RUNG:01.06.2016
Število ogledov:6563
Število prenosov:277
Metapodatki:XML DC-XML DC-RDF
:
LIU, Mingqiang, MALOVRH, Sara in FRANKO, Mladen, 2016, Microfluidic flow injection thermal lens microscopy for high throughput and sensitive analysis of sub-μL samples. Analytical methods [na spletu]. 2016. Vol. 8. [Dostopano 2 april 2025]. DOI 10.1039/C6AY00932H. Pridobljeno s: https://repozitorij.ung.si/IzpisGradiva.php?lang=slv&id=2328
Kopiraj citat
  
Skupna ocena:
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
(0 glasov)
Vaša ocena:Ocenjevanje je dovoljeno samo prijavljenim uporabnikom.
Objavi na:Bookmark and Share


Podobna dela iz repozitorija:
  1. Optimiranje produktivnosti mehkega žarjenja
Postavite miškin kazalec na naslov za izpis povzetka. Klik na naslov izpiše podrobnosti ali sproži prenos.

Gradivo je del revije

Naslov:Analytical methods
Skrajšan naslov:Anal. Methods
Leto izida:2016
ISSN:ISSN 0003-2654

Gradivo je financirano iz projekta

Financer:Drugi - Drug financer ali več financerjev

Nazaj