1. Recommendations for reporting equivalent black carbon (eBC) mass concentrations based on long-term pan-European in-situ observationsMarjan Savadkoohi, Marco Pandolfi, Olivier Favez, Jean-Philippe Putaud, Konstantinos Eleftheriadis, Markus Fiebig, Philip Hopke, Paolo Laj, A. Wiedensohler, Griša Močnik, 2024, original scientific article Abstract: A reliable determination of equivalent black carbon (eBC) mass concentrations derived from filter absorption photometers (FAPs) measurements depends on the appropriate quantification of the mass absorption cross-section (MAC) for converting the absorption coefficient (babs) to eBC. This study investigates the spatial–temporal variability of the MAC obtained from simultaneous elemental carbon (EC) and babs measurements performed at 22 sites. We compared different methodologies for retrieving eBC integrating different options for calculating MAC including: locally derived, median value calculated from 22 sites, and site-specific rolling regression MAC. The eBC concentrations that underwent correction using these methods were identified as LeBC (local MAC), MeBC (median MAC), and ReBC (Rolling MAC) respectively. Pronounced differences (up to more than 50 %) were observed between eBC as directly provided by FAPs (NeBC; Nominal instrumental MAC) and ReBC due to the differences observed between the experimental and nominal MAC values. The median MAC was 7.8 ± 3.4 m2/g from 12 aethalometers at 880 nm, and 10.6 ± 4.7 m2/g from 10 MAAPs at 637 nm. The experimental MAC showed significant site and seasonal dependencies, with heterogeneous patterns between summer and winter in different regions. In addition, long-term trend analysis revealed statistically significant (s.s.) decreasing trends in EC. Interestingly, we showed that the corresponding corrected eBC trends are not independent of the way eBC is calculated due to the variability of MAC. NeBC and EC decreasing trends were consistent at sites with no significant trend in experimental MAC. Conversely, where MAC showed s.s. trend, the NeBC and EC trends were not consistent while ReBC concentration followed the same pattern as EC. These results underscore the importance of accounting for MAC variations when deriving eBC measurements from FAPs and emphasizes the necessity of incorporating EC observations to constrain the uncertainty associated with eBC. Keywords: equivalent black carbon, mass absorption cross-section, filter absorption photometers, elemental carbon, absorption, site specific MAC, rolling MAC Published in RUNG: 04.03.2024; Views: 330; Downloads: 3 Full text (2,46 MB) This document has many files! More... |
2. |
3. Periodic anti-phase boundaries and crystal superstructures in ▫$PtCu_3$▫ nanoparticles as fuel cell electrocatalystsAna Rebeka Kamšek, Anton Meden, Iztok Arčon, Primož Jovanovič, Martin Šala, Francisco Ruiz-Zepeda, Goran Dražić, Miran Gaberšček, Marjan Bele, Nejc Hodnik, 2023, original scientific article Published in RUNG: 19.09.2023; Views: 830; Downloads: 5 Full text (2,15 MB) This document has many files! More... |
4. |
5. Effect of the Morphology of the High-Surface-Area Support on the Performance of the Oxygen-Evolution Reaction for Iridium NanoparticlesLeonard Moriau, Marjan Bele, Živa Marinko, Francisco Ruiz-Zepeda, Gorazd Koderman, Martin Šala, Angelija Kjara Šurca, Janez Kovač, Iztok Arčon, Primož Jovanovič, Nejc Hodnik, Luka Suhadolnik, 2021, original scientific article Abstract: The development of affordable, low-iridium-loading,
scalable, active, and stable catalysts for the oxygen-evolution
reaction (OER) is a requirement for the commercialization of
proton-exchange membrane water electrolyzers (PEMWEs).
However, the synthesis of high-performance OER catalysts with
minimal use of the rare and expensive element Ir is very challenging
and requires the identification of electrically conductive and stable
high-surface-area support materials. We developed a synthesis
procedure for the production of large quantities of a nanocomposite
powder containing titanium oxynitride (TiONx) and Ir.
The catalysts were synthesized with an anodic oxidation process
followed by detachment, milling, thermal treatment, and the
deposition of Ir nanoparticles. The anodization time was varied to grow three different types of nanotubular structures exhibiting different lengths and wall thicknesses and thus a variety of properties. A comparison of milled samples with different degrees of nanotubular clustering and morphology retention, but with identical
chemical compositions and Ir nanoparticle size distributions and dispersions, revealed that the nanotubular support morphology is
the determining factor governing the catalyst’s OER activity and stability. Our study is supported by various state-of-the-art
materials’ characterization techniques, like X-ray photoelectron spectroscopy, scanning and transmission electron microscopies, Xray powder diffraction and absorption spectroscopy, and electrochemical cyclic voltammetry. Anodic oxidation proved to be a very suitable way to produce high-surface-area powder-type catalysts as the produced material greatly outperformed the IrO2 benchmarks
as well as the Ir-supported samples on morphologically different TiONx from previous studies. The highest activity was achieved for the sample prepared with 3 h of anodization, which had the most appropriate morphology for the effective removal of oxygen
bubbles. Keywords: electrocatalysis, oxygen-evolution reaction, TiONx-Ir powder catalyst, iridium nanoparticles, anodic oxidation, morphology−activity correlation Published in RUNG: 04.01.2021; Views: 2600; Downloads: 0 This document has many files! More... |
6. |
7. Projekt predelave stroja za poliranje obročnih ključevJožef Petelinek, 2020, master's thesis Abstract: V magistrskem delu je opisana izvedba projekta predelave stroja za poliranje obročnih ključev. V prvem delu je opisano stanje stroja pred predelavo, razlogi za predelavo ter priprava zagonskega elaborata projekta predelave. V drugem delu je opisana izvedba projekta predelave. Ta zajema izdelavno nove električne vezalne sheme, izdelavo programa za krmilnik in operacijski panel, vezavo nove krmilne omare in vgradnjo teh komponent v omenjeni stroj. V zadnjem delu magistrskega dela je predstavljen postopek izdelave tehnične dokumentacije, potrebne za ponovni zagon stroja. Keywords: avtomatizacija, stroj za poliranje, programabilni logični krmilnik, projektno vodenje, tehnična dokumentacija Published in RUNG: 13.03.2020; Views: 3414; Downloads: 110 Full text (2,29 MB) |
8. Synthesis of a Cu/ZnO Nanocomposite by Electroless Plating for the Catalytic Conversion of CO2 to MethanolMaja Pori, Iztok Arčon, Damjan Lašič Jurković, Marjan Marinšek, Goran Dražić, Blaž Likozar, Zorica Crnjak Orel, 2019, original scientific article Abstract: The process of methanol synthesis based on the hydrogenation of CO2
was investigated over binary Cu/ZnO catalyst materials,
prepared by applying a novel electroless plating fabrication method. The activity of the produced catalytic samples
was determined at temperature range between 200 and 300 °C and the feedstock conversion data were supplemented with
a detailed microstructure analysis using high-resolution transmission electron microscopy (HRTEM), X-ray powder diffraction
(XRD) and Cu and Zn K-edge, X-ray absorption near-edge structure (XANES) measurements and extended X-ray
absorption fine-structure (EXAFS) measurements. It was confirmed that the disorder in the Cu crystallites created unique
geometrical situations, which acted as the additional reactive centres for the adsorption of the reactant molecule species.
Copper and zinc structural synergy (spill-over) was also demonstrated as being crucial for the carbon dioxide’s activation.
EXAFS and XANES results provide strong evidence for surface alloying between copper and zinc and thus the present results
demonstrate new approach applicable for explaining metal–support interactions. Keywords: EXAFS, CuZn alloy, Spillover mechanism, CO2 valorization, Electroless deposition method, Heterogeneous
catalysis Published in RUNG: 12.04.2019; Views: 3632; Downloads: 0 This document has many files! More... |
9. Electrochemical dissolution of iridium and iridium oxide particles in acidic media : transmission electron microscopy, electrochemical flow cell coupled to inductively coupled plasma mass spectrometry and X-ray absorption spectroscopy studyPrimož Jovanovič, Nejc Hodnik, Francisco Ruiz-Zepeda, Iztok Arčon, Barbara Jozinović, Milena Zorko, Marjan Bele, Martin Šala, Vid Simon Šelih, Samo B. Hočevar, Miran Gaberšček, 2017, original scientific article Abstract: Iridium based particles as the most promising proton exchange membrane electrolyser electrocatalysts were investigated
by transmission electron microscopy (TEM), and by coupling of electrochemical flow cell (EFC) with online inductively
coupled plasma mass spectrometer (ICP-MS). Additionally, a thin-film rotating disc electrode (RDE), an identical location transmission
and scanning electron microscopy (IL-TEM and IL-SEM) as well as an X-ray absorption spectroscopy (XAS) studies have
been performed. Extremely sensitive online time-and potential-resolved electrochemical dissolution profiles revealed that iridium
particles dissolved already well below oxygen evolution reaction (OER) potentials, presumably induced by iridium surface oxidation
and reduction processes, also referred to as transient dissolution. Overall, thermally prepared rutile type IrO2 particles (T-IrO2)
are substantially more stable and less active in comparison to as prepared metallic (A-Ir) and electrochemically pretreated (E-Ir)
analogues. Interestingly, under OER relevant conditions E-Ir particles exhibit superior stability and activity owing to the altered
corrosion mechanism where the formation of unstable Ir(>IV) species is hindered. Due to the enhanced and lasting OER performance,
electrochemically pre-oxidized E-Ir particles may be considered as the electrocatalyst of choice for an improved low temperature
electrochemical hydrogen production device, namely a proton exchange membrane electrolyser. Keywords: Iridium Oxide Par-ticles, Electrochemical Dissolution of Iridium, Ir L3-edge XANES Published in RUNG: 23.08.2017; Views: 3914; Downloads: 0 This document has many files! More... |
10. Atomically resolved dealloying of structurally ordered Pt nanoalloy as an oxygen reduction reaction electrocatalystAndraž Pavlišič, Primož Jovanovič, Vid Simon Šelih, Martin Šala, Marjan Bele, Goran Dražić, Iztok Arčon, Samo B. Hočevar, Anton Kokalj, Nejc Hodnik, Miran Gaberšček, original scientific article Abstract: The positive effect of intermetallic ordering of platinum alloy nanoparticles on oxygen reduction reaction (ORR) activity has been well established. What is still missing is an understanding of selective leaching of the less noble metal from the ordered structure and its correlation to longterm ORR performance. Using a combination of kinetic Monte Carlo simulations and advanced characterization techniques, we provide unprecedented insight into dealloying of intermetallic PtCu3 nanoparticles a well-known binary alloy. Comparison of ordered and disordered samples with identical initial compositions and particle size distributions reveals an unexpected correlation: whereas the copper dealloying rates in the ordered and disordered counterparts are almost the same, in the ordered structure Pt atoms are surrounded by 15−30% more Cu atoms throughout all the stages of acid leaching. This more convenient Pt−Cu coordination explains the statistically significant increase of 23−37% in ORR activity of the ordered structure at all stages of alloy degradation. Keywords: ORR activity, fuel cells, platinum alloy, nanoparticle stability, intermetallic ordering, kinetic Monte Carlo, dealloying, in situ ICP-MS Published in RUNG: 27.09.2016; Views: 5649; Downloads: 0 This document has many files! More... |